Siemens pureform DCF UDCMC30LL Dispersion Compensation -507.20 ps/nm
Siemens Optical Attenuators. Model: UDCMC30LL.
- Model
- Siemens UDCMC30LL
- Calibration
- Available on request
- Price
- $630
- Status
- In stock
- RFQ ref
- UDCMC30LL
This unit
The Siemens pureform DCF UDCMC30LL is a Dispersion Compensation Module (DCM) engineered to counteract chromatic dispersion in optical fiber communication systems. It delivers a dispersion compensation value of -507.20 ps/nm, preserving signal integrity across long-distance, high-speed transmissions. This single-mode fiber module is essential infrastructure for telecommunications networks where signal fidelity directly impacts system reach and capacity.
Technical Specifications
- Dispersion Compensation Value: -507.20 ps/nm
- Fiber Type: Single-Mode Fiber
- Insertion Loss: Typically low, minimizing signal attenuation
- Polarization Mode Dispersion (PMD): Typically low, critical for high-bit-rate signal quality
- Total Dispersion Slope: Managed across wavelength range for DWDM applications
- Operating Temperature Range: -20°C to +70°C (storage)
- Relative Humidity: 5% to 95% (non-condensing)
Key Features
- Negative dispersion compensation (-507.20 ps/nm) for pre- or post-transmission equalization
- Single-mode fiber construction for compatibility with standard G.652 optical fiber
- Low insertion loss and PMD characteristics for minimal signal degradation
- Dispersion slope management across operating wavelengths
Typical Applications
- DWDM system dispersion compensation
- SDH/SONET long-haul optical transport
- High-speed optical network transmission reach extension
- Data center interconnect systems requiring chromatic dispersion correction
Compatibility & Integration Designed for integration into optical transmission systems supporting DWDM, OTDM, and SDH platforms. Compatible with standard single-mode optical fiber per G.652 specifications. Module-based form factor enables integration into rack-mounted optical transmission equipment.
Siemens UDCMC30LL — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Siemens UDCMC30LL. Calibration covers attenuation accuracy at 5 or more set values across the full range (0 to rated maximum dB), attenuation linearity, wavelength-dependent attenuation at 1310 nm, 1490 nm, and 1550 nm, insertion loss at minimum attenuation (0 dB position), and polarization-dependent loss (PDL) where applicable. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Siemens UDCMC30LL faults: motor and gear mechanism wear (attenuation steps or loss of smooth control), optical port contamination, EEPROM calibration data corruption. Most common faults are motor or gear mechanism wear on variable attenuators causing attenuation steps or loss of smooth control, optical port contamination reducing dynamic range, and EEPROM calibration data corruption on digitally controlled models.
Siemens UDCMC30LL price
This Siemens UDCMC30LL is listed at $630. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Siemens UDCMC30LL calibration cost
NIST-traceable calibration for the Siemens UDCMC30LL is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers attenuation accuracy at 5 or more set values across the full range (0 to rated maximum dB), attenuation linearity, wavelength-dependent attenuation at 1310 nm, 1490 nm, and 1550 nm, insertion loss at minimum attenuation (0 dB position), and polarization-dependent loss (PDL) where applicable. Turnaround is 1 to 3 business days after receipt. See full calibration details →
