IEC F34 Function Signal Generator
IEC Function Generators. Frequency range: 0.03 Hz to 3 MHz.
- Model
- IEC F34
- Calibration
- Available on request
- Price
- $135
- Status
- In stock
- RFQ ref
- F34
This unit
The IEC F34 Function Signal Generator is a versatile signal source engineered for electronic testing, measurement, and R&D applications across educational and commercial laboratories. It generates fundamental waveforms - sine, square, triangle, pulse, and ramp - with adjustable DC offset, spanning frequencies from 0.03 Hz to 3 MHz and output amplitudes to 10 V peak-to-peak into 50 Ohms.
Technical Specifications
Waveform Generation- Sine, square, triangle, pulse (variable width), ramp (up and down), and DC offset
- Frequency range: 0.03 Hz to 3 MHz
- Output amplitude: 10 V peak-to-peak into 50 Ohm impedance
- DC offset: ±10 V (peak voltage not to exceed 10 V total) Frequency Control
- Calibrated coarse-fine tune controls with 1000:1 manual tuning range
- Speed-sensitive frequency knob for rapid approximation and fine adjustment
- Up/Down buttons for incremental frequency adjustment
- Voltage Controlled Generator (VCG) input: 0–10 V external control with proportional frequency modulation Amplitude Control
- Output adjustment knob
- 5-step attenuator with up to 60 dB attenuation
- DC offset switch: selectable positive, negative, or zero offset Sweep Capability
- Linear and logarithmic sweep modes
- Direct-reading sweep limits
- Sweep initiation and stop control Additional Features
- Trigger and gate modes with external synchronization
- Output limit indicator
- 50 Ohm coaxial output impedance
- Analog frequency display with digital readout for voltage, current, and waveform data
- Status indicators for offset, sweep, and standby modes Power
- AC input: 115 V or 230 V selectable, 50–400 Hz Dimensions
- 260 mm (W) × 70 mm (H) × 270 mm (D)
Key Features
- 1000:1 manual tuning range for precise frequency control
- Variable-width pulse and ramp generation
- Dual-mode sweep (linear/logarithmic) with programmable limits
- External VCG control for automated or modulated operation
- Multi-attenuator design for wide dynamic range
- Selectable AC mains voltage for global deployment
Typical Applications Circuit development and validation, component characterization, frequency response testing, educational demonstrations, and signal integrity analysis in laboratory and R&D environments.
Compatibility & Integration External voltage control (0–10 V VCG input) enables integration with automated test systems, modulation sources, and feedback control loops. Standard 50 Ohm output impedance supports direct connection to most laboratory instruments and RF test equipment.
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 0.03 Hz to 3 MHz | Voltage / Current Range: 10 V peak-to-peak output (50 Ohm) |
IEC F34 — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the IEC F34. Calibration covers output frequency accuracy, output amplitude accuracy at 50 ohm and Hi-Z load, DC offset accuracy, symmetry and duty cycle accuracy, and arbitrary waveform sample rate accuracy. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common IEC F34 faults: BNC output connector wear, output amplifier failure from short-circuit drive, display and keypad membrane switch wear, DDS or DAC failure on 33250A. HP 33120A and Agilent 33220A most common fault is BNC output connector wear from repeated cable insertions. Output amplifier failure on the HP 33120A typically results from sustained short-circuit drive. Agilent 33250A DDS and high-speed DAC failures are rare but require component-level repair and post-repair amplitude verification across the full 80 MHz range.
IEC F34 price
This IEC F34 is listed at $135. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
IEC F34 calibration cost
NIST-traceable calibration for the IEC F34 is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers output frequency accuracy, output amplitude accuracy at 50 ohm and Hi-Z load, DC offset accuracy, symmetry and duty cycle accuracy, and arbitrary waveform sample rate accuracy. Turnaround is 1 to 3 business days after receipt. See full calibration details →
