Asset Intertech RIC-1000 ScanWorks Remote Instrumentation Controller
The Asset Intertech RIC-1000 ScanWorks Remote Instrumentation Controller is a key component of the ScanWorks platform, offering remote access and control for boundary scan testing and in-system programming. It facilitates efficient testing and diagnostics of electronic assemblies, enabling streamlined validation and debugging processes.
- Model
- Asset Intertech RIC-1000
- Calibration
- Available on request
- Price
- $1,800
- Status
- In stock
- RFQ ref
- RIC-1000
This unit
The Asset Intertech RIC-1000 ScanWorks Remote Instrumentation Controller is a networked boundary scan controller that bridges ScanWorks software on a host PC with remote units under test via Ethernet. The device distributes test intelligence through the ScanWorks Embedded Instrumentation Engine (EIE) architecture, executing pre-stored tests from onboard memory to streamline validation, debugging, and in-system programming operations. It enables remote access and control over standard TCP/IP connectivity, making it suitable for distributed test environments and field operations.
Technical Specifications Boundary Scan Interface
Single Test Access Port (TAP) conforming to IEEE 1149.1 (JTAG)
Maximum TCK frequency: 50 MHz, selectable in 36 increments from 160 kHz to 50 MHz
PAUSE-DR state support for devices requiring hold states during shift operations Discrete I/O (DIO)
Eight bidirectional non-boundary scan DIO signals
DIO0 supports Write Enable (WE) function for flash programming
DIO1 monitors Ready/BUSY signals
Included UUT cable supports four DIO signals; custom cable required for remaining four Logic Level Support
UUT interface voltages: 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.3 V
Software-configurable via ScanWorks hardware configuration Networking
Auto-sensing 10/100/1000 Mbps Ethernet (CAT5E/6)
TCP/IP protocol
Initial IP assignment via USB flash drive text file; reconfigurable via telnet
Factory-assigned permanent MAC address Power
Supplied with 5 V, 4 A AC-DC power supply
Key Features
Distributed test architecture reduces computational load on host PC
EMI-resistant rugged enclosure design
Software-controlled TAP and DIO voltage levels
Efficient remote test execution from onboard memory
Typical Applications
Remote boundary scan and JTAG testing
In-system flash programming and firmware updates
Board-level validation and debug operations
Multi-site test environments over Ethernet infrastructure
Compatibility & Integration The RIC-1000 integrates with the Asset Intertech ScanWorks platform, requiring ScanWorks host software for operation and configuration. Included Accessories
One 2 ft RIC-1000 UUT cable
One 2 m CAT5E Ethernet cable
One 5 V 4 A AC-DC power supply
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 160 kHz to 50 MHz | Voltage / Current Range: 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V (UUT interface) |
Asset Intertech RIC-1000 — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Asset Intertech RIC-1000. Calibration covers analog input channel accuracy and offset at all gain settings, analog output accuracy, digital I/O logic threshold verification, sample rate and timing accuracy, and trigger and synchronization bus functional verification. NI CompactRIO and PXI chassis also undergo backplane trigger line integrity check.. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Asset Intertech RIC-1000 faults: power supply failure (cRIO-9073/9074), C-series slot connector wear, PXI chassis fan failure, GPIB interface failure on VXI controllers, BIOS/EEPROM corruption. NI CompactRIO most common faults are power supply failure on older cRIO-9073/9074 chassis and C-series module slot connector wear from repeated hot-swap cycles. PXI chassis fan failure is the most common wear item — chassis fans are field-replaceable. VXI embedded controllers most commonly develop EEPROM corruption and GPIB interface failure.
Asset Intertech RIC-1000 price
This Asset Intertech RIC-1000 is listed at $1,800. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Asset Intertech RIC-1000 calibration cost
NIST-traceable calibration for the Asset Intertech RIC-1000 is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers analog input channel accuracy and offset at all gain settings, analog output accuracy, digital I/O logic threshold verification, sample rate and timing accuracy, and trigger and synchronization bus functional verification. NI CompactRIO and PXI chassis also undergo backplane trigger line integrity check.. Turnaround is 1 to 3 business days after receipt. See full calibration details →
