Anritsu 69397B Ultra Low Noise Synthesized Sweep/Signal Generator
The Anritsu 69397B is a Ultra Low Noise Synthesized Sweep/Signal Generator. It delivers high-performance signal generation with ultra-low phase noise. It features synthesized sweep functionality, and is ideal for demanding applications requiring precise and clean signals.
- Model
- Anritsu 69397B
- Calibration
- Available on request
- Price
- $36,770
- Status
- In stock
- RFQ ref
- 69397B
This unit
The Anritsu 69397B is an ultra-low noise synthesized sweep/signal generator delivering precision RF and microwave signal generation from 0.1 Hz to 65 GHz in a single coaxial output, with extension to 110 GHz via millimeter wave source modules. The instrument combines ultra-low phase noise performance, flexible sweep modes, and comprehensive modulation capabilities for exacting test, measurement, and development applications.
Technical Specifications
Frequency and Output- Frequency range: 0.1 Hz to 65 GHz (single coaxial output); up to 110 GHz with waveguide extensions
- Output power: +17 dBm maximum; -125 dBm minimum; guaranteed leveled output to +17 dBm up to 20 GHz
- Accurately leveled output down to -120 dBm in 0.01 dB steps
- Frequency resolution: 1 kHz minimum step size (0.1 Hz with Option 11)
- Output power level accuracy: 0.01 dB steps Phase Noise and Spurious Performance
- Ultra-low SSB phase noise: -107 dBc at 10 kHz offset from 10 GHz
- Spurious signals: < -60 dBc Sweep Functionality
- Sweep modes: Linear, logarithmic, step, and alternate
- Sweep time range: 30 ms to 99 seconds
- Sweep width: 1 kHz to full range (0.1 Hz minimum with Option 11)
- Sweep speed accuracy: ≤ ±30 MHz or ±2 MHz widths for sweep speeds ≤ 50 MHz/ms
- Step sweep: 1 to 10,000 steps; 1 ms to 99 seconds dwell time
- List sweep: Up to 4 tables with 2,000 non-sequential frequency/power sets
- Digital frequency and power sweep supported Modulation Capabilities
- Internal modulation: AM, FM, phase modulation, pulse modulation
- Modulating waveforms: 7 internal waveforms including Gaussian noise; user-defined arbitrary waveforms supported
- Pulse modulation: Single and multiple pulses with swept delay for moving target simulation, radar blind spot testing, and recovery time testing
- External modulation: AM/FM/pulse modulation via external signals supported
Key Features
- Single-output simplicity to 65 GHz; millimeter wave extension capability
- Fine-resolution frequency tuning and power leveling for precise signal control
- Multiple sweep architectures for diverse measurement scenarios
- Advanced pulse modulation for radar and dynamic testing
- Arbitrary waveform support for custom modulation requirements
Typical Applications
- RF and microwave component characterization
- Radar system testing and validation
- Phase noise measurement and analysis
- Receiver sensitivity and selectivity testing
- Modulation fidelity assessment
Compatibility & Integration Anritsu millimeter wave source modules extend operating range to 110 GHz. User-downloaded arbitrary modulation enables integration with external signal processing workflows.
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 0.1 Hz to 65 GHz (single coaxial output) |
| up to 110 GHz with waveguide extensions | Power Range (dBm) | '-125 dBm to +17 dBm |
Anritsu 69397B — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Anritsu 69397B. Calibration covers output frequency accuracy, output power level accuracy across the full frequency range, AM/FM/PM/pulse modulation accuracy, harmonic and spurious output levels, and phase noise floor verification. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Anritsu 69397B faults: YIG oscillator failure (no output or loss of lock), step attenuator wear (output drops or steps at set attenuation), ALC loop failure (uncontrolled output power), I/Q modulator assembly failure. HP/Agilent 836xx series most common faults are YIG oscillator failure and step attenuator contact wear causing output steps or drops at specific attenuation settings. Keysight E4428C/E4438C units most commonly develop ALC loop failure and I/Q modulator assembly faults. YIG oscillator replacement and attenuator service are stocked repairs.
Anritsu 69397B price
This Anritsu 69397B is listed at $36,770. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Anritsu 69397B calibration cost
NIST-traceable calibration for the Anritsu 69397B is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers output frequency accuracy, output power level accuracy across the full frequency range, AM/FM/PM/pulse modulation accuracy, harmonic and spurious output levels, and phase noise floor verification. Turnaround is 1 to 3 business days after receipt. See full calibration details →
