Anritsu 69385A Synthesized Sweep/Signal Generator, 0.5 – 60 GHz
Anritsu RF Signal Sources. Frequency range: 0.5 GHz to 60 GHz, Accuracy: ±1.0 dB at +10 dBm (1 GHz).
- Model
- Anritsu 69385A
- Calibration
- Available on request
- Price
- $25,400
- Status
- In stock
- RFQ ref
- 69385A
This unit
The Anritsu 69385A is a synthesized sweep/signal generator delivering precise RF and microwave signal generation across 0.5 GHz to 60 GHz. It combines multiple sweep modes - linear, logarithmic, list, and frequency hop - with comprehensive modulation capabilities (AM, FM, and pulse) to address demanding production testing, R&D, and system integration workflows. The instrument offers output power from -120 dBm to +20 dBm with frequency switching under 50 ms and amplitude switching under 20 ms, ensuring rapid stimulus application across broadband test scenarios.
Technical Specifications
Frequency & Switching- Frequency range: 0.5 GHz to 60 GHz
- Frequency switching speed: < 50 ms (typical, between any two frequencies)
- Amplitude switching speed: < 20 ms (typical)
- Residual FM: < 2 Hz RMS at 1 GHz carrier Output Power
- Range: -120 dBm to +20 dBm (typical, frequency dependent)
- Output impedance: 50 Ohms
- VSWR: < 2.0:1 (typical)
- Power accuracy: ±1.0 dB at +10 dBm (1 GHz); ±1.5 dB at +10 dBm (10 GHz); ±2.0 dB at +0 dBm (60 GHz) Signal Purity
- Phase noise: <-105 dBc/Hz at 10 kHz offset (1 GHz); <-100 dBc/Hz (10 GHz); <-90 dBc/Hz (60 GHz)
- Harmonic distortion: <-30 dBc (typical)
- Spurious signals: 60 dB on/off ratio, 100 ns to CW pulse width, 10 Hz to 100 kHz PRF
Key Features
- Four sweep modes for flexible test stimulus generation
- GPIB (IEEE-488) and Ethernet (LAN) for integrated test automation
- SCPI command support for programmable instrument control
- USB interface for firmware updates
Typical Applications
- Production testing of RF/microwave components and subsystems
- Component characterization in R&D laboratories
- System-level integration verification
- Broadband frequency response measurement
Compatibility & Integration Control via GPIB (IEEE-488), Ethernet (LAN), and USB interfaces. SCPI programming support enables integration into automated test environments and network-based measurement systems.
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 0.5 GHz to 60 GHz | Power Range (dBm): '-120 dBm to +20 dBm |
Anritsu 69385A — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Anritsu 69385A. Calibration covers output frequency accuracy, output power level accuracy across the full frequency range, AM/FM/PM/pulse modulation accuracy, harmonic and spurious output levels, and phase noise floor verification. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Anritsu 69385A faults: YIG oscillator failure (no output or loss of lock), step attenuator wear (output drops or steps at set attenuation), ALC loop failure (uncontrolled output power), I/Q modulator assembly failure. HP/Agilent 836xx series most common faults are YIG oscillator failure and step attenuator contact wear causing output steps or drops at specific attenuation settings. Keysight E4428C/E4438C units most commonly develop ALC loop failure and I/Q modulator assembly faults. YIG oscillator replacement and attenuator service are stocked repairs.
Anritsu 69385A price
This Anritsu 69385A is listed at $25,400. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Anritsu 69385A calibration cost
NIST-traceable calibration for the Anritsu 69385A is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers output frequency accuracy, output power level accuracy across the full frequency range, AM/FM/PM/pulse modulation accuracy, harmonic and spurious output levels, and phase noise floor verification. Turnaround is 1 to 3 business days after receipt. See full calibration details →
