Abaco Systems / VMIC VMIVME-2128-301 128-bit High-Voltage Digital Output Board with Built-In-Test
Abaco Systems / VMIC VME Modules. Voltage / Current Range: 5 to 48 VDC output; 600 mA sink per channel; 3.0 A @ +5 VDC logic supply, Channels: 128 channels, Current: 990 mA maximum before automatic shutdown.
- Model
- Abaco Systems / VMIC VMIVME-2128-301
- Calibration
- Available on request
- Price
- $1,599
- RFQ ref
- VMIVME-2128-301
This unit
The Abaco Systems / VMIC VMIVME-2128-301 is a 128-bit high-voltage digital output board for VMEbus systems, delivering software-controlled switching and load management in industrial and embedded control applications. Built-in test (BIT) logic enables per-channel operational verification without external instrumentation. Open-collector drivers sink up to 600 mA continuous current with 990 mA surge capability, making the board suitable for driving lamps, solenoids, stepper motors, and relay coils across voltage classes from 5 V to 48 VDC.
Technical Specifications
- Output Channels: 128 channels, individually addressable
- Output Type: High-voltage open-collector drivers
- Voltage Range: 5 to 48 VDC; 55 V maximum breakdown
- Current Sink: 600 mA continuous per channel
- Surge Current: 990 mA maximum before automatic shutdown
- Data Transfer: 8-bit, 16-bit, and 32-bit modes
- Form Factor: Double Eurocard, 6U height
- Power Draw: 3.0 A typical at +5 VDC (logic supply)
- Operating Temperature: 0 to +55 °C
- VMEbus Compliance: ANSI/IEEE STD 1014-1987, IEC 821 and 297
Key Features
- Built-in test logic for software-controlled channel diagnostics
- Automatic inrush current shutdown protection
- Thermal shutdown protection on all output drivers
- Output clamp diodes for inductive load transient suppression
- Optional pull-up resistors for electronic switch outputs (5 V to 55 V configurations)
- User-supplied warming resistor sockets for current management
- Flexible addressing within VMEbus I/O space (short and standard supervisory/non-privileged modes)
Interfaces & Connectors
- Two 96-pin female connectors (P3, P4) support both mass termination (IDC) and discrete wire configurations
- ERNI No. 913 031 IDC mating connectors recommended with 0.033-inch ribbon cable
- Harting No. 09 03 096 3214 discrete wire option with crimp contacts and shell housing
- P2 connector for user-supplied power and ground; VMIACC-0132 power accessory available
Typical Applications Digital switching, lamp drivers, solenoid control, stepper motor excitation, relay coil driving, multi-load industrial automation systems, and VME-based embedded control platforms requiring per-channel status verification.
Specifications
| Parameter | Value |
|---|---|
| Voltage / Current Range | 5 to 48 VDC output |
Abaco Systems / VMIC VMIVME-2128-301 — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Abaco Systems / VMIC VMIVME-2128-301. All calibrations are performed to NIST-traceable standards and ship with a certificate. Turnaround is typically 1–3 business days after receipt.
Abaco Systems / VMIC VMIVME-2128-301 price
This Abaco Systems / VMIC VMIVME-2128-301 is listed at $1,599. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Abaco Systems / VMIC VMIVME-2128-301 calibration cost
NIST-traceable calibration for the Abaco Systems / VMIC VMIVME-2128-301 is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Turnaround is 1 to 3 business days after receipt. See full calibration details →
