Anritsu MS2723C
Anritsu Spectrum Analyzers. Frequency Range: ** 9 kHz to 13 GHz, Dynamic Range: ** >, Accuracy: ** ±25 ppb (GPS ON).
- Model
- Anritsu MS2723C
- Calibration
- Available on request
- Price
- $8,500
- RFQ ref
- MS2723C
This unit
The Anritsu MS2723C is a handheld spectrum analyzer covering 9 kHz to 13 GHz, engineered for field spectrum monitoring, interference analysis, and wireless communication system testing. It delivers dynamic range exceeding 104 dB in 1 Hz resolution bandwidth and displayed average noise level of –160 dBm (preamp ON). Sweep speeds reach 100× faster than previous generations across three modes: Fast, Performance, and No FFT. Frequency accuracy of ±25 ppb with GPS and amplitude accuracy of ±0.7 dB typical (±1.25 dB maximum) support demanding RF measurements from DANL to +30 dBm.
Technical Specifications
Frequency Range: 9 kHz to 13 GHz
Resolution Bandwidth (RBW): 1 Hz to 10 MHz
Video Bandwidth (VBW): 1 Hz to 10 MHz
Dynamic Range: >104 dB (1 Hz RBW)
DANL: –160 dBm (1 Hz RBW, preamp ON)
Phase Noise: –100 dBc/Hz @ 10 kHz offset at 1 GHz
Frequency Accuracy: ±25 ppb (GPS ON)
Amplitude Accuracy: ±0.7 dB typical; ±1.25 dB maximum (15°C to 35°C)
Power Measurement Range: DANL to +30 dBm
Power Requirements: 8 to 18 Vdc via USB
Battery Life: Approximately 2.5 hours (Li-Ion)
Warm-up Time: <5 minutes
Key Features
Trace modes: Normal, Max Hold, Min Hold, Average with configurable averaging
Six markers with delta capability or single reference with six delta markers
Up to 40 segment limit lines with automated envelope creation
Save-on-Event trigger for trace capture at limit line crossing or sweep completion
Channel power measurement: Occupied Bandwidth, Channel Power, ACPR
Optional Interference Analysis includes Spectrogram, Signal Strength, RSSI, and on-screen Interference Mapping
Optional Modulation Analysis covers RF Spectrum, Audio Spectrum, Audio Waveform, and Demodulation Summary
Optional 3GPP/3GPP2 signal analyzers for LTE, TD-LTE, GSM/EDGE, W-CDMA/HSPA+, CDMA, and EV-DO
Optional IEEE 802.16 analyzers for Fixed and Mobile WiMAX
Optional Channel Scanner (1 to 2 channels)
Optional GPS receiver for enhanced frequency accuracy and data tagging
Interfaces & Integration
Data Transfer: Ethernet/USB
External Reference: BNC female, 50 Ω input (–10 to +10 dBm); 10 MHz output
External Trigger: BNC female, 50 Ω (±5 VDC maximum)
IF Output: 140 MHz on BNC female, 50 Ω
Headset Jack: 2.5 mm, 3-wire
Optional High Accuracy Power Meter requires external power sensor
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 9 kHz to 13 GHz | Power Range (dBm): '+30 dBm to -160 dBm |
Anritsu MS2723C — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Anritsu MS2723C. All calibrations are performed to NIST-traceable standards and ship with a certificate. Turnaround is typically 1–3 business days after receipt.
Anritsu MS2723C price
This Anritsu MS2723C is listed at $8,500. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Anritsu MS2723C calibration cost
NIST-traceable calibration for the Anritsu MS2723C is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Turnaround is 1 to 3 business days after receipt. See full calibration details →
