Agilent/Keysight E1413A
Agilent / Keysight VXI Modules. Channels: Typical Applications.
- Model
- Agilent / Keysight E1413A
- Calibration
- Available on request
- Price
- $1,500
- Status
- In stock
- RFQ ref
- E1413A
This unit
The Agilent/Keysight E1413A is a single-width, C-size VXI data acquisition module that delivers high-speed analog-to-digital conversion for multi-channel measurement systems. It combines 16-bit resolution at up to 100 kHz sampling rate with a 64-channel FET multiplexer and on-board signal conditioning support via plug-on modules, enabling voltage, temperature, strain, and resistance measurements across mixed-signal applications.
Technical Specifications
- Analog-to-Digital Conversion: 16-bit resolution; 100,000 samples per second maximum
- Multiplexer: 64-channel FET configuration
- Data Buffer: 65,024 reading FIFO buffer (dual-ported, 64 kSa capacity); supports Circular Buffer or Block mode
- Data Format: IEEE 754 32-bit floating-point
- Current Value Table (CVT): 64 channel data registers in A24 address space for rapid display and control loop access
- Gain & Offset Correction: Per-channel correction at full scanning rate
- VXI Interface: A16 and A24 address space; SCPI and Compiled SCPI programming support
Key Features
- On-board calibration sources enable single-command, all-channel calibration
- Engineering Unit (EU) conversion performed at full speed on-board
- System wiring offset compensation per channel
- Signal Conditioning Plug-on (SCP) module support: accepts up to eight SCP modules in any mix
- Compatible SCP modules include E1501A through E1538A series
- Optional E1413-60001 Direct Input SCP card provides 8 additional channels
Typical Applications
- Real-time data acquisition in VXI-based test systems
- Multi-parameter monitoring requiring mixed-signal transducers
- High-speed scanning across distributed sensor arrays
- Temperature, strain, and resistance measurement networks
- PID loop feedback and control system integration
Compatibility & Integration Operates as a single VXI module within standard C-size slot architecture. Register-based interface sustains maximum acquisition rate; controllers such as the Radusis EPC-VII maintain full speed with dual E1413A configurations writing to disk at 900 KB/sec. Extended device addressing supports both A16 and A24 register spaces.
Agilent / Keysight E1413A — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Agilent / Keysight E1413A. Calibration covers all module-specific parameters per manufacturer datasheet, output accuracy and linearity, frequency accuracy, and VXI register and trigger bus compliance. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Agilent / Keysight E1413A faults: relay contact wear, DAC/ADC drift, VXI backplane connector oxidation. Common faults include relay contact wear, DAC or ADC gain drift, and VXI backplane edge connector oxidation. Most modules are repaired at the component level with full post-repair verification in a C-size or D-size mainframe.
Agilent / Keysight E1413A price
This Agilent / Keysight E1413A is listed at $1,500. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Agilent / Keysight E1413A calibration cost
NIST-traceable calibration for the Agilent / Keysight E1413A is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers all module-specific parameters per manufacturer datasheet, output accuracy and linearity, frequency accuracy, and VXI register and trigger bus compliance. Turnaround is 1 to 3 business days after receipt. See full calibration details →
