Fluke 179-2/IMSK Industrial Multimeter Service Kit
Fluke Industrial Test Equipment. Voltage: 600.0 mV to 1000 V, Current: 60.00 mA.
- Model
- Fluke 179-2/IMSK
- Calibration
- Available on request
- Price
- $430
- Status
- In stock
- RFQ ref
- 179-2/IMSK
This unit
The Fluke 179-2/IMSK Industrial Multimeter Service Kit pairs the Fluke 179 True-RMS Digital Multimeter with essential accessories for electrical diagnostics in industrial environments. The Fluke 179 delivers True-RMS AC/DC measurements, resistance, capacitance, frequency, continuity, diode testing, and temperature measurement. Its 6000-count display with analog bar graph and backlight enables rapid troubleshooting in field conditions. Manual and automatic ranging modes adapt to changing measurement scenarios. Data Hold, Auto Hold, and Min/Max/Average recording functions capture signal behavior for analysis. The meter withstands transient impulses exceeding 8000 V and meets CAT III 1000 V and CAT IV 600 V overvoltage ratings.
Technical Specifications Measurement Ranges & Accuracy
DC Voltage: 600.0 mV to 1000 V; ±(0.09% + 2)
AC Voltage: 600.0 mV to 1000 V; ±(1.0% + 3)
DC Current: 60.00 mA, 600.0 mA, 10.00 A; ±(1.0% + 3)
AC Current: 60.00 mA, 600.0 mA, 10.00 A; ±(1.5% + 3)
Resistance: 600.0 Ω to 50.00 MΩ; ±(0.9% + 1)
Capacitance: 10.00 nF to 10,000 µF; ±(1.2% + 2)
Frequency: 0.01 Hz to 100 kHz; ±(0.1% + 1)
Temperature: -40°C to 400°C; ±(1.0% + 10) Display & Power
6000-count digital display with analog bar graph; backlit for low-light visibility
9V battery; approximately 200 hours runtime
Key Features
True-RMS measurement for accurate readings on non-sinusoidal AC signals
Integrated temperature sensor for -40°C to 400°C range measurement
Closed-case front-panel calibration capability
Overmolded case and integrated protective holster for field durability
Transient protection rated to exceed 8000 V impulses
Typical Applications Electrical system diagnostics, preventive maintenance circuits, motor and transformer testing, HVAC troubleshooting, industrial control panel commissioning.
Safety & Ratings CAT III 1000 V / CAT IV 600 V overvoltage category; meets transient impulse withstand requirements.
Specifications
| Parameter | Value |
|---|---|
| Frequency Range | 0.01 Hz to 100 kHz | Voltage / Current Range: 10.00 A, 600.0 mA, DC: 600.0 mV to 1000 V |
| AC | 600.0 mV to 1000 V |
| Current | 60.00 mA |
Fluke 179-2/IMSK — Repair & Calibration Service
Aumictech offers NIST-traceable calibration and repair for the Fluke 179-2/IMSK. Calibration covers DC voltage accuracy at all ranges, AC voltage (True RMS) accuracy at 50 Hz, 1 kHz, and 10 kHz, DC current accuracy, resistance accuracy at all decade ranges, frequency accuracy, and diode test voltage. Fluke 87V and 289 also include capacitance and temperature calibration.. All calibrations ship with a NIST-traceable certificate. Turnaround is typically 1–3 business days after receipt.
Common Fluke 179-2/IMSK faults: blown input fuse, worn input jacks, display segment failure, relay contact wear on bench DMMs. Common faults include worn input jacks (banana socket contact wear on the mA and COM terminals), blown input fuses (especially the 440 mA HRC fuse), and display segment failures. Keithley 2000/2001/2002 bench DMMs commonly develop relay contact wear affecting resistance accuracy after extended service.
Fluke 179-2/IMSK price
This Fluke 179-2/IMSK is listed at $430. Calibration is available separately from $450. Contact us for volume pricing or if you need multiple units.
Fluke 179-2/IMSK calibration cost
NIST-traceable calibration for the Fluke 179-2/IMSK is $450 (standard — pass/fail certificate and calibration sticker) or $650 (full measured data at every test point, reference standards documented, traceability chain included). Calibration for this instrument covers DC voltage accuracy at all ranges, AC voltage (True RMS) accuracy at 50 Hz, 1 kHz, and 10 kHz, DC current accuracy, resistance accuracy at all decade ranges, frequency accuracy, and diode test voltage. Fluke 87V and 289 also include capacitance and temperature calibration.. Turnaround is 1 to 3 business days after receipt. See full calibration details →
